Raypak 055B Instrukcja Użytkownika

Part No. 240428CATALOG NO. 6100.52-OEffective: 07-01-02Replaces: 04-01-02INSTALLATIONAND OPERATINGINSTRUCTIONSModels055BVERSASPAandHOT TUB HEATERThis

10HIGH WIND CONDITIONS (OUTDOOR UNITS ONLY)In areas where high winds are frequent, it may benecessary to locate the heater a minimum of 3' fromhi

VENT PIPINGWARNING: Indoor boilers require a draft hood thatmust be connected to a vent pipe and properly ventedto the outside. Failure to follow t

GAS SUPPLY CONNECTIONSGas piping must have a sediment trap aheadof the heater gas controls, and a manual shut-off valvelocated outside the heater jack

13PLUMBING FOR WATER CONNECTIONSLOCATIONThe VERSA heater requires water flow and posi-tive pressure to fire and operate properly. It musttherefore be

throughout its entire length and must pitch downwardfrom the valve. No shut-off valve shall be installedbetween the relief valve and the drain line.

SPK15 WIRING DIAGRAM KEYFig. # 8096Fig. # S86/S8600 S86 S8600PINK CONNECTOR BLUE CONNECTORFor 120 V input power to the unit, connect

WIRING DIAGRAM MILLIVOLT UNITSWITH MECHANICAL THERMOSTAT WIRING DIAGRAM MILLIVOLT UNITS WITH SOLID STATE THERMOSTATFig. # 2246eFig. # 235316If requi

17WIRING DIAGRAM 152178 Model 055 IIDBLBLBL

SECTION 4 / SERVICING INSTRUCTIONSGENERAL LOCATION OF CONTROLSDrain Valve Solid State Thermostat & Ignition ControlPressure SwitchBurner &a

PRESSURE SWITCH ADJUSTMENT:1. With pump and heater on, turn adjustmentknob (clockwise) until a click is heard from thegas valve.2. Turn adjustment kno

Contents2 PART ONE - Owner's Operating Instructions2 SECTION 1 / START-UP PROCEDURES2 Before Start-Up3 Lighting Instructions & Shut-Off Proce

BURNER DRAWER REMOVAL1. Shut off main electrical power switch to heater.2. Shut off gas upstream of heater.3. Remove front door.4. Disconnect gas line

DESOOTING PROCEDURECAUTION: SOOT IS COMBUSTIBLE. EXERCISEEXTREME CARE. NEVER USE A WIRE BRUSH.Soot can clog areas between fins and cause even-tual t

SECTION 5 / TROUBLE SHOOTING GUIDEIMPORTANT NOTICEThese instructions are primarily intended for the use of qualified personnel specifically trained a

If pilot burner remains lit.Jump across pressureswitch terminalsIf main burner does notfire, remove jumperCheck for adequate waterflow from filterRepl

ELECTRICAL (SOLID STATE THERMOSTAT MILLIVOLT)If the pool/spa/hot tub water is too cold, troubleshoot the system as follows:Check voltage at + and - t

ELECTRICAL (ELECTRONIC IGNITION IID)WARNINGHIGH VOLTAGEFor qualified Technicians ONLYNOTE: Some heaters may be equipped withan ignition module that s

ELECTRICAL (SOLID STATE THERMOSTAT IID)If the pool/spa/hot tub water is too cold, troubleshoot the system as follows:Check voltage at 24 V terminals.

SECTION 6/REPLACEMENT PARTS LISTNOTE: To supply the correct part it is important thatyou state the model number, serial number and type ofgas when a

2813-P15-PIIDMV1-P14-P9-P12-P3-P7-P14-P5-PFig. #8132.0Fig. #8133.01-V7-C1-C2-C13-H12-H11-H6-H5-H4-H10-H1-S2-S3-H7-H2-H2-V4-S1-R5-M3-S7-M6-C5-C3-C1-M2-

29

PART ONE - OWNER'S OPERATING INSTRUCTIONSSECTION 1 / START-UP PROCEDURESBEFORE START-UPBURNERSClean main burners and air louvers of dust, lint an

30

LIMITED WARRANTYRAYPAK RESIDENTIAL SWIMMING POOL & SPA HEATERSGENERALRaypak, Inc. warrants that all parts of this product will be free from def

Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 FAX (800) 872-9725Raypak Canada LTD, 2805 Slough Street, Mississauga, Ontario, Cana

1. STOP! Read the safety information above.2. Set the thermostat on the lowest setting.3. Turn On/Off switch to the "Off" position.4. Remove

TO TURN OFF GAS TO APPLIANCE51. STOP! Read the safety information above.2. Set the thermostat to the lowest setting.3. Turn off all electric power to

AFTER START-UPFeel the inlet and outlet pipes. Outlet pipe should beonly slightly warmer than the inlet. It should not be hot.WARNING: Should overheat

4. Make visual check of the burner and pilot flame.Flame pattern on the main burner and pilot isindicated in the previous illustration. Yellowflame me

PART 2 - INSTALLATION / SERVICE INSTRUCTIONSSECTION 1 / RECEIVING EQUIPMENTOn receipt of your equipment it is suggested that youvisually check for ext

9ALL HEATERSFor clearances from combustible surfaces, seechart below.Clearances from Combustible construction.Indoor Installation:Top* (Drafthood) - 3